Skip to main content
Request a Quote Schedule a Demo
Close

Grain Augers

Built By Experience

The same employees have been building our grain augers for 20 plus years. If that doesn’t suggest expertise, we don’t know what does.

Request a Quote Schedule a Demo

Models

  • Portable Bin Sweep

    • This bin sweep works to the floor of about 1/4 revolutions and the balance of grain is removed in one to two revolutions. A stabilizer wheel comes standard on 8″ sweeps in 30′, 36′, 42′, and 48′ lengths, and on all 10″ lengths.

    • Option 1

      • Sweep Size: 6″
      • Flighting: 4″ OD x 11 Ga. Flighting
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Bin Sizes: 18′-36′

    • Option 2

      • Sweep Size: 8″
      • Flighting: 5.25″ OD x 11 Ga. Flighting
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Bin Sizes: 18′-48′

    • Option 3

      Sweep Size: 10″

      Flighting: 9″ OD x 3/16″ Flighting

      Flighting Shaft: 2³/⁸” OD x 2″ ID

      Bin Sizes: 30′-75′

Externally Powered Bin Sweep

      • Quick connect flange clamp
      • A stabilizer wheel comes standard on 8″ sweeps in 30′, 36′, 42′, and 48′ lengths, and on all 10″ lengths.

    • Option 1

      • Sweep Size: 6″
      • Hopper Size: 20.5″ x 20.5″ x 12″ Deep
      • Tube: 6″ OD x 16 Ga. Galv.
      • Unloading & Sweep Flighting Assembly: 5¹/⁴” OD x 11 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′-36′

    • Option 2

      • Sweep Size: 8″
      • Hopper Size: 20.5″ x 20.5″ x 12″ Deep
      • Tube: 8″ OD x 14 Ga. Galv.
      • Unloading & Sweep Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′-48′

    • Option 3

      • Sweep Size: 10″
      • Hopper Size: 20″ x 20″ x 14″ Deep
      • Tube: 10″ OD x 12 Ga. Galv.
      • Unloading & Sweep Flighting Assembly: 9″ OD x 3/16″ Flighting on 2³/⁸” OD Shaft
      • Bin Sizes: 30′ – 75′

Bin Hopper & Unloading Tube with Flight Assembly

      • Quick connect flange clamp
      • Intermediate bin wall hopper with side gate
      • Intermediate concrete hopper (standard on 10″)
      • Bin wall flange
      • Intermediate bin wall hopper

    • Option 1

      • Size: 6″
      • Type: Drying Floor or Aeration Installation
      • Hopper Size: 13.5″ x 13.5″ x 13 Deep
      • Tube: 6″ OD x 16 Ga. Galv.
      • Flighting Assembly: 5.25″ OD x 11 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′-36′

    • Option 2

      • Size: 6″
      • Type: Concrete Slab Installation
      • Hopper Size: 13.5″ x 13.5″ 7.25″ Deep
      • Tube: 6″ OD x 16 Ga. Galv.
      • Flighting Assembly: 5.25″ OD x 11 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′-36′

    • Option 3

      • Size: 8″
      • Type: Drying Floor or Aeration Installations
      • Hopper Size: 13.5″ x 13.5″ x 13 Deep
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′ – 60′

    • Option 4

      • Size: 8″
      • Type: Concrete Slab Installation
      • Hopper Size: 13.5″ x 13.5″ x 13 9.25″ Deep
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flighting Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′ – 60′

    • Option 5

      • Size: 10″
      • Type: Drying Floor or Aeration Installations
      • Hopper Size: 20″ x 20″ x 14″ Deep
      • Tube: 10″ OD x 12 Ga. Galv.
      • Flighting Assembly: 9″ OD x ³/¹⁶” Flighting on 2³/⁸” OD Shaft
      • Bin Sizes: 30′ – 75′

    • Option 6

      • Size: 10″
      • Type: Concrete Slab Installation
      • Hopper Size: 13.5″ x 13.5″ x 11.25″ Deep
      • Tube: 10″ OD x 12 Ga. Galv.
      • Flighting Assembly: 9″ OD x ³/¹⁶” Flighting on 2³/⁸” OD Shaft
      • Bin Sizes: 30′ – 75′

25 Degree Angle Powerhead

      • Quick connect flange clamp
      • Discharge sprout

    • Option 1

      • Size: 6″ to 8″
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flight Assembly: 7″ OD x 10 Ga. Flight on 1.5″ OD Shaft
      • Bin Sizes: 18′ – 36′

    • Option 2

      • Size: 8″ to 10″
      • Tube: 10″ OD x 12 Ga. Galv.
      • Flight Assembly: 9″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
      • Bin Sizes: 18′ – 60′

    • Option 3

      • Size: 10″ to 12″
      • Tube: 12″ OD x 10 Ga. Galv.
      • Flight Assembly: 11″ OD x 3/16″ Flight on 2³/⁸” OD Shaft
      • Bin Sizes: 30′ – 75′

Adjustable Angle Adapter

    • Option 1

      • Size: 6″
      • Power Unit Required: H-81 or C-802 | 8″ Units with 1.25″ ID Center Shaft
      • Bin Sizes: 18′ – 36′

    • Option 2

      • Size: 8″
      • Power Unit Required: HC-100 or C-1003 | 10″ Units with 2″ ID Center Shaft
      • Bin Sizes: 18′ – 60′

    • Option 3

      • Size: 10″
      • Power Unit Required: HC-120 or C-1200 | 12: Units with 2″ ID Center Shaft
      • Bin Sizes: 30′ – 75′

Vertical Powerhead

      • Quick connect flange clamp

    • Option 1

      • Horizontal Tube: 6″
      • Horizontal Flighting: 5¹/⁴” OD x 11 Ga. Flighting on 1.5″ OD Shaft
      • Vertical Tube: 8″ OD x 14 Ga. Galv.
      • Vertical Flighting: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • 14’10” or 19’10”
      • Bin Sizes: 18′ – 36′

    • Option 2

      • Horizontal Tube: 8″
      • Horizontal Flighting: HC-100 or C-1003 | 10″ Units with 2″ ID Center Shaft
      • Vertical Tube: 8″ OD x 14 Ga. Galv.
      • Vertical Flighting: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • 14’10” or 19’10”
      • Bin Sizes: 18′ – 48′

Horizontal Powerhead

      • Quick connect flange clamp

    • Option 1

      • Size: 6″
      • Tube: 6″ OD x 16 Ga. Galv. x 18″ Long
      • Flight Assembly: 5¹/⁴” OD x 11 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′ – 36′

    • Option 2

      • Size: 8″
      • Tube: 8″ OD x 14 Ga. Galv. x 18″ Long
      • Flight Assembly: 7″ OD x 10 Ga. Flighting on 1.5″ OD Shaft
      • Bin Sizes: 18′ – 60′

    • Option 3

      • Size: 10″
      • Tube: 10″ OD x 12 Ga. Galv. x 24″ Long
      • Flight Assembly: 9″ OD x ³/¹⁶” Ga. Flighting on 2³/⁸” OD Shaft
      • Bin Sizes: 30′ – 75′

D/DR Series: Distributing Augers

    • This distributing auger series is the textbook definition of versatile. This conveying system can be utilized to fill a multiple bin installation or can be used for unloading. Because grain flow can be reversed, you can get even greater flexibility out of your system.

      • Flow-thru intake hopper
      • Outlet with side gate
      • Rectangular-square adaptor
      • Outlet assembly with side gate
      • Cable control kit
      • Inlet
      • 45-degree square elbow
      • Two-way pan valve
      • Square to round adaptor
      • Square to round flanged adaptor
      • Mounting bracket

      *Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.

    • Option 1

      • Size: 6″
      • Tube: 6″ x 16 Ga. Galv.
      • Drive Type: Cast Iron Drive Sheave and 8″ Section Belt
      • Basic Length: 21′-196′
      • 1-15 HP
      • Up to 750 BPH @ 340 RPM | Up to 890 BPH @ 404 RPM

    • Option 2

      • Size: 8″
      • Tube: 8″ x 14 Ga. Galv.
      • Drive Type: 3:1 Chain Reducer 10 HP Cast Iron Drive Sheave and “B” Section Belts
      • Basic Length: 20′-200′
      • 1-15 HP
      • Up to 895 BPH @ 169 RPM | 1265 BPH @ 239 RPM | 1615 BPH @ 305 RPM

H Series: Horizontal, Vertical or Inclined Augers

    • This auger series pulls grain from an intake to a single discharge without intermediate bearings, unlike the other guys.

      *Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.

    • Option 1

      • Size: 6″
      • Basic Length: 6′, 11′ 16′, & 21′
      • Tube: 6″ OD x 16 Ga. Galv.
      • Flighting: 5³/¹⁶” OD x 11 Ga.
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Drive: 14″ OD Cast Iron Sheave and “B” Section Belts
      • Capacity: Up to 1170 BPH

    • Option 2

      • Size: 8″
      • Basic Length: 6′, 11′ 16′, & 21′
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flighting: 7″ OD x 10 Ga.
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Drive: 14″ OD Cast Iron Sheave and “B” Section Belts
      • Capacity: Up to 2820 BPH

HC Series: Reduced Pitch Augers

    • The HC Series is no stranger to the custom game. Choose your pitch, extensions, and accessories to create the perfect auger to address your needs.

      *Reduced pitch flighting is preferred for handling moisture grain.

      • Intake support
      • Intake hopper
      • Flow-thru intake hopper
      • Mounting brackets
      • Tube splice
      • 30, 45, and 90-degree discharge spouts
      • 45-degree square elbow
      • Two-way pan valve
      • Three-way pan valve
      • Square to round adaptor
      • Square to round flanged adaptor
      • Spouting
        • Not all accessories are available for all augers
      • 1/2 pitch
      • 3/4 pitch
      • Full pitch
      • Extensions section available in 7.5′, 10′, 15′, and 20′ lengths

      *Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.

    • Option 1

      • Size: 6″
      • Basic Length: 3.5′ w/ choice of pitch
      • Flighting: 5³/¹⁶” OD x 11 Ga.
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Drive: 14″ OD Cast Iron Sheave, and “B” Section Belt(s)
      • Capacity: Up to 1170 BPH

    • Option 2

      • Size: 8″
      • Basic Length: 3.5′ w/ choice of pitch
      • Flighting: 7″ OD x 10 Ga.
      • Flighting Shaft: 1.5″ OD x 1.25″ ID
      • Drive: 14″ OD Cast Iron Sheave and “B” Section Belt(s)
      • Capacity: Up to 2820 BPH

    • Option 3

      • Size: 10″
      • Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
      • Flighting: 9″ OD x 3/16
      • Flighting Shaft: 2³/⁸” OD x 2″ ID
      • Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
      • Capacity: Up to 4515 BPH

    • Option 4

      • Size: 12″
      • Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
      • Flighting: 11″ OD x 3/16
      • Flighting Shaft: 2³/⁸” OD x 2″ ID
      • Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
      • Capacity: Up to 8200 BPH

Bulk Tank Unloaders

    • These augers can be used in any horizontal, inclined, or vertical position. Bulk Tank Unloaders are the practical solution for permanent installation as a bulk tank or subfloor auger. Portable applications include unloading trucks to bins, bins to trucks, or bins to mills.

      • Extensions available in 10′, 15′, and 20′ lengths
      • Mounting bracket
      • Flexible tube spout
      • Discharge spout

      *Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.

    • Option 1

      • Size: 6″
      • Basic Length: 5′, 7.5′, 10′, and 15′
      • Tube: 6″ OD x 16 Ga. Galv.
      • Flighting Assembly: 5³/¹⁶” OD x 11 Ga.
      • Drive: 12″ OD “B” Section Pressed Steel Sheave
      • Capacity: Up to 780 BPH @ 45° | Up to 1040 BPH @ Horiz.

    • Option 2

      • Size: 8″
      • Basic Length: 10′, 15′, and 20′
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flighting Assembly: 7″ OD x 10 Ga.
      • Drive: 12″ OD “B” Section ≤ 15′ and 14″ OD “B” Section 20′-50′
      • Capacity: Up to 1860 BPH @ 45° | Up to 2480 BPH @ Horiz.

    • Option 3

      • Size: 10″
      • Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
      • Tube: 9″ OD x 3/16
      • Flighting Assembly: 2³/⁸” OD x 2″ ID
      • Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
      • Capacity: Up to 4515 BPH

    • Option 4

      • Size: 12″
      • Basic Length: 6.5′, 11.5′, 16.5′, and 21.5′ w/ choice of pitch
      • Tube: 11″ OD x 3/16
      • Flighting Assembly: 2³/⁸” OD x 2″ ID
      • Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
      • Capacity: Up to 8200 BPH

Bin Roof Augers

    • *Capacities (or horsepower) may vary with type and condition of grain, auger RPM, type, and amount of exposed flighting and degree of incline.

    • Option 1

      • Size: 6″
      • Hopper: 19.5 L x 16″ H x 18″ W
      • Tube: 6″ OD x 16 Ga. Galv.
      • Flighting Assembly: 5³/¹⁶” OD x 11 Ga.
      • Drive: 14″ OD Cast Iron Sheave, “B” Section Belt(s)
      • Capacity: Up to 975 BPH @ 30°

    • Option 2

      • Size: 8″
      • Hopper: 19.5 L x 18″ H x 18″ W
      • Tube: 8″ OD x 14 Ga. Galv.
      • Flighting Assembly: 7″ OD x 10 Ga.
      • Drive: 14″ OD Cast Iron Sheave, “B” Section Belt(s)
      • Capacity: Up to 2070 BPH @ 30°

    • Option 3

      • Size: 10″
      • Hopper: 24″ L x 24″ H x 24″ W
      • Tube: 10″ OD x 12 Ga. Galv.
      • Flighting Assembly: 9″ OD x 7 Ga.
      • Drive: 19″ OD Cast Iron Sheave “3V” Section Belts
      • Capacity: Up to 3770 BPH @ 30°

Available Lengths

    • AVAILABLE LENGTHS RECOMMENDED FOR BIN DIAMETER
      6″ & 8″ 10″
      11′ N/A 21′
      13.5′ N/A 24′
      16′ N/A 27′
      18.5′ N/A 30′
      21′ 21′ 36′
      26′ 26′ 42′
      28.5′ 31′ 48′
      36′ 36′ 60′

ELEVATE YOUR EQUIPMENT KNOWLEDGE

Stay up-to-date with the latest product launches and gain invaluable insights into Bazooka Farmstar’s innovative manure-handling equipment.

Learn More

Renegade Agitation Trailer

This website uses cookies for analytics, personalization and advertising. To learn more or change your cookie settings, please read our privacy policy. By continuing to browse, you agree to our use of cookies.

Accept